User Tools

Site Tools


sensors:gnss

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
sensors:gnss [2012/07/25 15:27]
karina [Specifications]
sensors:gnss [2012/11/06 15:29]
karina
Line 11: Line 11:
 169.254.1.2\\ 169.254.1.2\\
 169.254.1.3\\ 169.254.1.3\\
 +
 +====== Help ======
 +[[sensors:gnss:Synchronized|Synchronized]]
 +[[sensors:gnss:low_latency|Low latency]]
 +
  
 ====== Documentation ====== ====== Documentation ======
Line 33: Line 38:
 ^Physical specifications^^ ^Physical specifications^^
 |**Feature**| **Specification**| |**Feature**| **Specification**|
-|Dimensions (L x W x H)|24 cm (9.4 in) x 12 cm (4.7 in) x 5 cm (1.9 in) including connectors|+|Dimensions (LxWxH)|24 cm (9.4 in) x 12 cm (4.7 in) x 5 cm (1.9 in) including connectors|
 |Weight|1.65 kg (3.64 lbs) receiver with internal battery and radio| |Weight|1.65 kg (3.64 lbs) receiver with internal battery and radio|
 | |1.55 kg (3.42 lbs) receiver with internal battery and no radio| | |1.55 kg (3.42 lbs) receiver with internal battery and no radio|
Line 46: Line 51:
 |- Vibration|MIL-STD-810F, Fig 514.5C-17| |- Vibration|MIL-STD-810F, Fig 514.5C-17|
 |Measurements|Advanced Trimble Maxwell(TM) Custom GPS chip\\ Proven Trimble low elevation tracking technology| |Measurements|Advanced Trimble Maxwell(TM) Custom GPS chip\\ Proven Trimble low elevation tracking technology|
 +
 +^Electrical specifications^^
 +|**Feature**| **Specification**|
 +|Power||
 +|- Internal|Integrated internal battery 7.4 V, 7800 mA-hr, Lithium-ion Internal battery operates as a UPS in the event of external power source outage\\ Internal battery will charge from external power source when input voltage is >15 V\\ Integrated charging circuitry|
 +|- External|Power input on Lemo 7-P0S is optimized for lead acid batteries with a cut-off threshold of 10.5 V\\ Power source supply (Internal / External) is hot-swap capable in the event of power source removal or cut off 9 V to 30 V DC external power input with over-voltage protection\\ Receiver will automatically turn on when connected to external power source of 15 V or greater|
 +|Power consumption|<8 W in RTK Base mode with internal transmit radio|
 +|Base station operation times on internal battery|Typically 8–10 hours based on transmitter power, types of messages transmitted, and temperature|
 +|Rover operation times on internal battery|Typically 12 hours, varies with temperature.|
 +|Certification|Part 15.247 and Part 90 FCC certifications\\ Class B Device FCC Part 15 and ICES-003 certifications\\ RSS-310, RSS-210 and RSS-119 Industry Canada certifications\\ ACMA AS/NZS 4295 approval\\ CE mark compliance\\ C-tick mark compliance\\ UN ST/SG/AC 10.11/Rev. 3 Amend. 1 (Li-ion Battery)\\ UN ST/SG/AC 10/27/Add. 2 (Li-ion Battery)\\ WEEE|
 +
 +
 +^Communication specifications^^
 +|**Feature**| **Specification**|
 +|Communications||
 +|- Port 1 (7-pin 0S Lemo)|3-wire RS-232/CAN|
 +|- Port 2 (D-sub 26-pin)|Full RS-232 (through multi-port adaptor)\\ 3-wire RS-232|
 +|- Bluetooth|USB (On the Go)\\ Ethernet\\ Fully-integrated, fully-sealed 2.4 GHz Bluetooth*|
 +|Integrated radios (optional)|Fully-integrated, fully-sealed internal 450 MHz, Tx, Rx, or Tx/Rx\\ Fully-integrated, fully-sealed internal 900 MHz, Tx, Rx, or Tx/Rx|
 +|- Channel spacing (450 MHz)|12.5 KHz or 25 KHz spacing available|
 +|- Frequency approvals (900 MHz)|USA (-10), Australia (-30), New Zealand (-20)|
 +|- 450 MHz transmitter radio power output|0.5 W / 2.0 W|
 +|- 900 MHz transmitter radio power output|1.0 W|
 +|Data output|Proprietary Trimble Ag CMR+|
 +|*Bluetooth type approvals are country specific. For more information, contact your local Trimble office or representative.||
 +
 +
 +
  
  
sensors/gnss.txt · Last modified: 2021/08/14 04:21 (external edit)