This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
sensors:tiltmeter [2012/09/11 14:50] karina [Performance Specifications (1*)] |
sensors:tiltmeter [2013/10/21 13:58] claes [Software] |
||
---|---|---|---|
Line 10: | Line 10: | ||
|User manual| {{: | |User manual| {{: | ||
|Data sheet|{{: | |Data sheet|{{: | ||
+ | |||
+ | ===== Software ===== | ||
+ | {{: | ||
+ | |||
+ | {{: | ||
===== Links ===== | ===== Links ===== | ||
Line 45: | Line 50: | ||
| ::: ||Repeatability||± 0.1 μT| | | ::: ||Repeatability||± 0.1 μT| | ||
- | (1*) Specifications are subject to change. Assumes the TCM is motionless and the local magnetic field is clean relative to the calibration. | + | (1*) Specifications are subject to change. Assumes the TCM is motionless and the local magnetic field is clean relative to the calibration. |
- | (2*) For example, if the calibration was performed over ±10° of tilt, then the TCM would provide <2° rms accuracy over ±20° of tilt. | + | (2*) For example, if the calibration was performed over ±10° of tilt, then the TCM would provide <2° rms accuracy over ±20° of tilt.\\ |
(3*) Performance at maximum operational dip angle will be somewhat degraded. | (3*) Performance at maximum operational dip angle will be somewhat degraded. | ||
==== Operating Characteristics ==== | ==== Operating Characteristics ==== | ||
- | ^Parameter^Value^ | + | |
+ | === I/O Characteristics === | ||
+ | |||
+ | ^Parameter^^Value^ | ||
|Communication Interface|TCM XB|Binary RS232 UART| | |Communication Interface|TCM XB|Binary RS232 UART| | ||
| ::: |TCM MB|Binary CMOS/TTL UART| | | ::: |TCM MB|Binary CMOS/TTL UART| | ||
Line 59: | Line 67: | ||
- | (1*) The maximum sample rate is dependent on the strength of the magnetic field, and typically will be from 25 to 32 samples/ | + | (1*) The maximum sample rate is dependent on the strength of the magnetic field, and typically will be from 25 to 32 samples/ |
(2*) FIR taps set to " | (2*) FIR taps set to " | ||
+ | === Power Requirements === | ||
+ | ^Parameter^^^Value^ | ||
+ | |Supply Voltage|TCM XB||3.6 to 5 VDC (unregulated)| | ||
+ | |:::|TCM MB||3.3 to 5 VDC (unregulated)| | ||
+ | |Average Current Draw|TCM XB|@ max. sample rate|20 mA typical| | ||
+ | |:::|:::|@ 8 Hz sample rate|16 mA typical| | ||
+ | |:::|TCM MB|@ max. sample rate|17 mA typical| | ||
+ | |:::| ::: |@ 8 Hz sample rate|13 mA typical| | ||
+ | |Peak Current Draw|During application of external power||120 mA pk, 60 mA avg over 2 ms| | ||
+ | |:::|During logical power up/down or Sync Trigger||100 mA pk, 60 mA avg over 4 ms| | ||
+ | |Sleep Mode Current Draw|||0.3 mA typical| | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | === Environmental Requirements === | ||
+ | ^Parameter^Value^ | ||
+ | |Operating Temperature (1*)|-40C to +85C| | ||
+ | |Storage Temperature|-40C to +85C| | ||
+ | |||
+ | (1*) To meet performance specifications, | ||
+ | ===== TCM Pin Descriptions ===== | ||
+ | ^Pin number^ | ||
+ | ^:::^9 pin connector^Pigtailed cable wire color^ | ||
+ | |1|GND|Black| | ||
+ | |2|GND|Grey| | ||
+ | |3|GND|Green| | ||
+ | |4|NC|Orange| | ||
+ | |5|NC|Violet| | ||
+ | |6|NC|Brown| | ||
+ | |7|UART Tx|Yellow| | ||
+ | |8|UART Rx|Blue| | ||
+ | |9|+5 VDC|Red| |