Differences

This shows you the differences between two versions of the page.

--- sensors:lsm111 [2012/09/10 14:57]
karina [(1*)(2*)(3*)]
+++ sensors:lsm111 [2021/08/14 04:21] (current)
@@ Line 10: / Line 10: @@
 LMS 1XX
 {{:sensors:How to store data on LMS1XX.pdf|How to store data using SICK Laser}}
+LMS 1XX
+{{:sensors:LMS1xx_LMS5xx_TiM3xx_JEF300_JEF500 Telegrams.pdf|LMS1xx Developer's guide}}
 {{:sensors:lms100.gif?200|}}
+SOPAS
+{{:sensors:setup.exe|SOPAS setup.exe}}
 ====== Specifications ======
@@ Line 18: / Line 24: @@
 |[[sensors:lsm111#Functional data|Functional data]]|
 |[[sensors:lsm111#General data|General data]]|
+|[[sensors:lsm111#Electrical data|Electrical data]]|
 |[[sensors:lsm111#(1*)(2*)(3*)|(1*)(2*)(3*)]]|
@@ Line 53: / Line 59: @@
 ^ ^Minimum^Typical^Maximum^
 |Laser protection class|Laser class 1 according IEC 60825H1 (2007H3) (complies with 21 CFR 1040.10 with the exception of the deviations as per Laser Notice No. 50, July 26, 2001)|||
-|Enclosure rating|As per EN 60529 (1991H10); A1 (2002H02)|||
+|**Enclosure rating**|As per EN 60529 (1991H10); A1 (2002H02)|||
 |- LMS100/LMS122/LMS123|IP 65|||
 |- LMS111/LMS151|IP 67|||
@@ Line 61: / Line 67: @@
 |**Operating temperature range**||||
 |- LMS100/LMS122/LMS123|0 °C (32 °F)| |+50 °C (122 °F)|
-|||||
+|- LMS111/LMS151|–30 °C (86 °F)| |+50 °C (122 °F)|
-|||||
+|Storage temperature range|–30 °C (86 °F)| |+70 °C (158 °F) max. 24 h|
-|||||
+|Humidity (taking into account the operating temperature range)|DIN EN 60068H2H61, method 1|||
-|||||
+|**Vibration resistance**|As per EN 60068H2H6 (1995H04)|||
-|||||
+|- Frequency range|10 Hz| |150 Hz|
-|||||
+|- Amplitude|5 g RMS| | |
-|||||
+|**Shock resistance**|As per EN 60068H2H27 (1993H03), EN 60068H2H29 (1993H04)|||
-|||||
+|- Single shock|15 g (0.53 oz), 11 ms|||
-|||||
+|- Continuous shock|10 g (0.35 oz), 16 ms|||
-|||||
+|**Sender**|Pulsed laser diode|||
-|||||
+|- Wave length|895 nm|905 nm|915 nm|
-|||||
+|- Divergence of the collimated beam (solid angle)| |15 mrad| |
-|||||
+|- Light spot size at the optics cover| |8 mm (0.32 in)| |
-|||||
+|- Light spot size at 18 m (59.05 ft) scanning range| |300 mm (11.82 in)| |
-|||||
+|**Housing**||||
-|||||
+|- Material|GDHALSI12 3.2582.05|||
-|||||
+|- Colour LMS100|RAL 5012 (blue)|||
-|||||
+|- Colour LMS122|RAL 9005 (black)|||
+|- Colour LMS123|RAL 9003 (white)|||
+|- Colour LMS111/LMS151|RAL 7032 (grey)|||
+|- Alloy|Excellent weather resistance as per DIN EN 106:1988, plate 3|||
+|**Optics cover**||||
+|- Material|Polycarbonate|||
+|- Surface finish|Outside with scratch-resistant coating|||
+|**System plug** (LMS100/LMS122/LMS123)||||
+|- Material|GDHALSI12 3.2582.05|||
+|- Colour LMS100/LMS122|RAL 9005 (black)|||
+|- Colour LMS123|RAL 9003 (white)|||
+|**Cable entries **(LMS111/LMS151)||||
+|- Material|Stainless steel/plastic|||
+|**Dimensions**(3*)||||
+|- Height LMS100/LMS122/LMS123| | |152 mm (5.99 in)|
+|- Height LMS111/LMS151| | |162 mm (6.38 in)|
+|- Width| | |102 mm (4.02 in)|
+|- Depth| | |106 mm (4.18 in)|
+|- Total weight (without connecting cables)| |1.1 kg (2.43 lb)||
+===== Electrical data =====
+^ ^Minimum^Typical^Maximum^
+|Supply voltage LMS100/LMS111/LMS151 SELV or PELV as per IEC 60364H4H41 (2005H12)|10.8 V|24 V|30 V|
+|Supply voltage LMS122/LMS123 SELV or PELV as per IEC 60364H4H41 (2005H12)|9 V|24 V|30 V|
+|Permissible residual ripple| | |±5%|
+|Supply voltage for the LMS111/LMS151 heating|19.2 V|24 V|28.8 V|
+|Switch on current| | |2 A|
+|Operating current at 24 V without output load| |0.35 A|0.5 A|
+|Operating current with max. output load| |0.65 A|0.8 A|
+|Operating current with maximum heating performance| |2.3 A|2.5 A|
+|Power consumption without output load| |8.4 W|12 W|
+|Power consumption with maximum output load| |16 W |20 W|
+|Power consumption with maximum heating performance| |55 W| 60 W|
+|Electrical connection LMS111/LMS151|Round M12 plug connector|||
+|Electrical connection LMS100/LMS122/LMS123|System plug with screw terminal block|||
+|**Technical specifications**, screw terminals||||
+|- Cross-section of rigid cores (American Wire Gauge — AWG)|0.14 mm2 (approx. 26 AWG)| |1.5 mm2 (approx. 16 AWG)|
+|- Cross-section of flexible cores (American Wire Gauge — AWG)|0.14 mm2 (approx. 26 AWG)| |1.0 mm2 (approx. 18 AWG)|
+|- Insulation stripping length for the cores| |5 mm (0.2 in)| |
+|- Screw tightening torque|0.22 Nm| |0.3 Nm|
+|**Cable length** for device power supply at 24 V||||
+|- With 1 mm2 wire cross-section (approx. 18 AWG)| | |220 m (721.78 ft)|
+|- With 0.5 mm2 wire cross-section (approx. 22 AWG)| | |110 m (360.89 ft)|
+|With 0.25 mm2 wire cross-section (approx. 24 AWG)| | |50 m (164.04 ft)|
+|**Cable length** for heating at 24 V||||
+|- With 1 mm2 wire cross-section (approx. 18 AWG)| | |45 m (147.64 ft)|
+|- With 0.5 mm2 wire cross-section (approx. 22 AWG)| | |20 m (65.62 ft)|
+|- With 0.25 mm2 wire cross-section (approx. 24 AWG)| | |10 m (32.81 ft)|
+|**Cable length** for device power supply at 12 V||||
+|- With 1 mm2 wire cross-section (approx. 18 AWG)| | |20 m (65.62 ft)|
+|- With 0.5 mm2 wire cross-section (approx. 22 AWG)| | |10 m (32.81 ft)|
+|- With 0.25 mm2 wire cross-section (approx. 24 AWG)| | |5m (16.40 ft)|
+|**Switching inputs**||||
+|- Number|2|||
+|- Input resistance on HIGH| |2 kΩ| |
+|- Voltage for HIGH|11 V|24 V|30 V|
+|- Voltage for LOW| |0 V|5 V|
+|- Input capacity| |15 nF| |
+|- Static input current|6 mA| |15 mA|
+|**Dynamic control inputs**||||
+|- Number|2|||
+|- Input resistance on HIGH| |2 kΩ| |
+|- Voltage for HIGH|11 V|24 V|30 V|
+|- Voltage for LOW|-3 V|0 V|5 V|
+|- Input capacity| |1 nF| |
+|- Static input current|6 mA| |15 mA|
+|- Duty cycle (Ti/T)| |0.5| |
+|- Input frequency| | |100 kHz|
+|- Current load per incremental encoder| |50 mA|100 mA|
+|**Velocity range that can be sampled**||||
+|- Forward|From +100 mm/s to +20,000 mm/s (3.94 in/s to +788 in/s)|||
+|- Backward|From –10 mm/s to –20,000 mm/s (–0.39 in/s to –788 in/s)|||
+|**Incremental encoders that can be evaluated**||||
+|- Type|Two-channel rotary encoder with 90° phase offset|||
+|- Enclosure rating|IP 54| | |
+|- Supply voltage|U<sub>V</sub> – 3 V| |U<sub>V</sub>|
+|- Outputs required on the incremental encoders|Push&/Pull|||
+|- Pulse frequency| | |100 kHz|
+|- Number of pulses per cm|50| | |
+|- Cable length (screened)| | |10 m (32.81 ft)|
+|**Digital switching outputs** LMS100/111/151||||
+|- Number|3|||
+|- Voltage drop load| |2 V| |
+|- Maximum switching current| | |140 mA|
+|- Current limiting (after 5 ms at 25°C (77 °F)|100 mA| |200 mA|
+|- Power-up delay|Negligible|||
+|- Switch off time| |0.8 ms|2 ms|
+|**Relay switching outputs** LMS122/123||||
+|- Number|2|||
+|- Switching capacity| | |DC 30 W/ AC 37,5 VA|
+|- Switching voltage| | |DC 110 V/ AC 125 V|
+|- Switching current| | |0.5 A at DC 30 V|
+|- Switching capacity| | |10μA DC 10 mV|
+|- Switching cycles|10<sup>5</sup>| | |
+|- Power-up delay| |2 ms|4 ms|
+|- Switch off time| |2 ms|4 ms|
+|**Serial auxiliary interface**||||
+|- Communication protocol|RSH232 (proprietary)|||
+|- Transmission speed|9,600 Baud|57.6 kBd|115.2 kBd|
+|**Serial host interface**||||
+|- Communication protocol|RSH232 (proprietary)|||
+|- Transmission speed (selectable)|9,600 Baud|57.6 kBd|115.2 kBd|
+|- Cable length at 38.400 kBd and wire cross- section 0.25 mm2 (approx. 24 AWG)| | |15 m (49.21 ft)|
+|- Galvanic de-coupling|Yes|||
+|- Wire cross-section of the connecting cable| | |0.25 mm2 (approx. 24 AWG)|
+|Ethernet|10/100 MBit/s|||
+|CAN|20 kBit/s, 500 kBit/s, 1 Mbit/s|||
 ===== (1*)(2*)(3*) =====

Technology in Crop Production

User Tools

Site Tools

Differences

Page Tools