This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
sensors:tiltmeter [2012/09/11 14:28] karina [PRODUCT SPECS] |
sensors:tiltmeter [2021/08/14 04:21] (current) |
||
---|---|---|---|
Line 10: | Line 10: | ||
|User manual| {{: | |User manual| {{: | ||
|Data sheet|{{: | |Data sheet|{{: | ||
+ | |||
+ | ===== Software ===== | ||
+ | {{: | ||
+ | |||
+ | {{: | ||
===== Links ===== | ===== Links ===== | ||
Line 21: | Line 26: | ||
http:// | http:// | ||
- | ===== PRODUCT | + | ===== PRODUCT |
- | ^**Parameter**^^^**Value**^ | + | ==== Performance Specifications (1*) ==== |
- | |Heading|Accuracy|≤65° of tilt after full range calibration|< | + | |
- | | ::: | ::: |≤80° of tilt after full range calibration|< | + | ^**Parameter**^^^^**Value**^ |
- | | ::: | ::: |≤5° of tilt after 2D calibration|< | + | |Heading|Accuracy|≤65° of tilt after full range calibration||<0.3° rms| |
- | | ::: | ::: |≤2 times the calibration tilt angle after limited-tilt calibration (2*)|< | + | | ::: | ::: |≤80° of tilt after full range calibration||<0.5° rms| |
- | | ::: |Resolution||0.1°| | + | | ::: | ::: |≤5° of tilt after 2D calibration||<2.0° rms| |
- | | ::: |Repeatability||0.05° rms| | + | | ::: | ::: |≤2 times the calibration tilt angle after limited-tilt calibration (2*)||<0.2° rms| |
- | |Tilt (Pitch & Roll)|Range|Pitch|± 90°| | + | | ::: |Resolution|||0.1°| |
- | | ::: | ::: |Roll|± 180°| | + | | ::: |Repeatability|||0.05° rms| |
- | | ::: |Accuracy|Pitch|0.2° rms| | + | |Tilt (Pitch & Roll)|Range|Pitch||± 90°| |
+ | | ::: | ::: |Roll||± 180°| | ||
+ | | ::: |Accuracy|Pitch||0.2° rms| | ||
| ::: | ::: |Roll|≤65° of pitch|0.2° rms| | | ::: | ::: |Roll|≤65° of pitch|0.2° rms| | ||
| ::: | ::: | ::: |≤80° of pitch|0.4° rms| | | ::: | ::: | ::: |≤80° of pitch|0.4° rms| | ||
| ::: | ::: | ::: |≤86° of pitch|1.0° rms| | | ::: | ::: | ::: |≤86° of pitch|1.0° rms| | ||
- | | ::: |Resolution||0.01°| | + | | ::: |Resolution|||0.01°| |
- | | ::: |Repeatability||0.05° rms| | + | | ::: |Repeatability|||0.05° rms| |
- | |Maximum Operational Dip Angle|||| | + | |Maximum Operational Dip Angle (3*)||||85°| |
- | ||||| | + | |Magnetometers||Calibrated Field Range||± 125 μT| |
- | ||||| | + | | ::: ||Resolution||0.05 μT| |
- | ||||| | + | | ::: ||Repeatability||± 0.1 μT| |
- | ||||| | + | |
- | ||||| | + | (1*) Specifications are subject to change. Assumes the TCM is motionless and the local magnetic field is clean relative to the calibration. \\ |
- | ||||| | + | (2*) For example, if the calibration was performed over ±10° of tilt, then the TCM would provide <2° rms accuracy over ±20° of tilt.\\ |
- | ||||| | + | (3*) Performance at maximum operational dip angle will be somewhat degraded. |
- | ||||| | + | |
- | ||||| | + | ==== Operating Characteristics ==== |
- | ||||| | + | |
- | ||||| | + | === I/O Characteristics === |
- | ||||| | + | |
+ | ^Parameter^^Value^ | ||
+ | |Communication Interface|TCM XB|Binary RS232 UART| | ||
+ | | ::: |TCM MB|Binary CMOS/TTL UART| | ||
+ | |Communication Rate||300 to 115200 baud| | ||
+ | |Maximum Sample Rate (1*)||≈30 samples/sec| | ||
+ | |Time to Initial Good Data (2*)|Initial power up|<210 ms| | ||
+ | | ::: |Sleep mode recovery|< | ||
+ | |||
+ | |||
+ | (1*) The maximum sample rate is dependent on the strength of the magnetic field, and typically will be from 25 to 32 samples/ | ||
+ | (2*) FIR taps set to " | ||
+ | |||
+ | === Power Requirements === | ||
+ | ^Parameter^^^Value^ | ||
+ | |Supply Voltage|TCM XB||3.6 to 5 VDC (unregulated)| | ||
+ | |:::|TCM MB||3.3 to 5 VDC (unregulated)| | ||
+ | |Average Current Draw|TCM XB|@ max. sample rate|20 mA typical| | ||
+ | |:::|:::|@ 8 Hz sample rate|16 mA typical| | ||
+ | |:::|TCM MB|@ max. sample rate|17 mA typical| | ||
+ | |:::| ::: |@ 8 Hz sample rate|13 mA typical| | ||
+ | |Peak Current Draw|During application of external power||120 mA pk, 60 mA avg over 2 ms| | ||
+ | |:::|During logical power up/down or Sync Trigger||100 mA pk, 60 mA avg over 4 ms| | ||
+ | |Sleep Mode Current Draw|||0.3 mA typical| | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | === Environmental Requirements === | ||
+ | ^Parameter^Value^ | ||
+ | |Operating Temperature (1*)|-40C to +85C| | ||
+ | |Storage Temperature|-40C to +85C| | ||
+ | |||
+ | (1*) To meet performance specifications, | ||
+ | ===== TCM Pin Descriptions ===== | ||
+ | ^Pin number^ | ||
+ | ^:::^9 pin connector^Pigtailed cable wire color^ | ||
+ | |1|GND|Black| | ||
+ | |2|GND|Grey| | ||
+ | |3|GND|Green| | ||
+ | |4|NC|Orange| | ||
+ | |5|NC|Violet| | ||
+ | |6|NC|Brown| | ||
+ | |7|UART Tx|Yellow| | ||
+ | |8|UART Rx|Blue| | ||
+ | |9|+5 VDC|Red| | ||
+ | |||
+ | ===== Source Code ===== | ||
- | (2*) For example, if the calibration was performed over ±10° of tilt, then the TCM would provide <2° rms accuracy over ±20° of tilt. |